satco/nuvo

Turn-knob LED dimmer in a phenolic housing, finished in black with black-and-gold knobs for a classic look on traditional lamp builds. Compatible w...

A 1 inch turned brass check ring with a 1/4 IP slip bore, finished in burnished and lacquered brass — the size that lands squarely between the smal...

Turned brass check ring measuring 1-1/2 inches in diameter with a 1/4 IP slip fit, wide enough for chandelier bodies and multi-arm assemblies. Burn...

Turned brass check ring at 3/4 inch diameter, drilled for a 1/4 IP slip fit — the larger-bore version for assemblies built around 1/4 IP nipples. B...

7/8 inch turned brass check ring sized for 1/4 IP slip fit — used where the assembly runs on the larger 1/4 IP nipple size. Burnished and lacquered...

Turned from solid brass at 1" diameter, sized for medium shade and shoulder retention on 1/4 IP builds. Unfinished stock for any final finish on to...

Solid brass turned to 1-1/2" diameter with a clean machined edge. The unfinished stock accepts plating, lacquer, or aged patinas, while the 1/4 IP ...

At 1-1/4" diameter, this turned brass check ring covers a medium-wide seat on 1/4 IP nipples — common on floor lamps and larger pendant builds. Fe...

Holds the next component in a 1/4 IP lamp stack at 1-1/8" diameter. The turned brass face works as both retainer and visible trim depending on wher...

At 1-3/4" diameter, this turned brass check ring gives substantial visible face on a 1/4 IP build — sized for wide shade retainers and decorative s...

An unfinished brass check ring at 1-3/8" diameter, slip fit for 1/4 IP nipples. Sized for broader shade retainers and shoulder work on heavier fixt...

Caps a 1/4 IP nipple stack at 1-5/8" diameter, locking the part below in contact with its shoulder. Wide enough to also serve as a visible trim dis...

An unfinished brass check ring at 1-7/8" diameter with a 1/4 IP slip fit. The wide turned face reads as visible trim on the assembly while doing th...

Turned brass check ring sized for 1/4 IP slip lamp pipe. The 2-inch diameter and unfinished surface make it easy to plate, lacquer, or patina to ma...

Sized at 3/4" diameter, this turned brass check ring sits at the small end of the 1/4 IP slip range — useful where the retainer needs to stay visua...

Slips over a 1/4 IP nipple and retains the next part in a heavier lamp stack — floor lamps, larger pendants, or any build using the 1/4 IP system i...

An unfinished brass check ring at 7/8" diameter with a 1/4 IP slip fit. The turned edge takes any finish, from polished plating to a natural patina...

A turned solid-brass check ring in a burnished and lacquered finish, sized to seat against a 1/8 IP slip fitting for shade holders and socket assem...

A turned solid-brass check ring in a burnished and lacquered finish, sized to seat against a 1/8 IP slip fitting for shade holders and socket assem...

A turned solid-brass check ring in a burnished and lacquered finish, sized to seat against a 1/8 IP slip fitting for shade holders and socket assem...

Larger 1-3/4 inch turned brass check ring with a 1/8 IP slip bore, sized for wider trim work in chandeliers and multi-arm fixtures. Burnished and l...

A 1/2 inch turned brass check ring with a 1/8 IP slip fit, finished in burnished and lacquered brass so it drops over a nipple as a decorative reta...

A turned solid-brass check ring in a burnished and lacquered finish, sized to seat against a 1/8 IP slip fitting for larger shade holders and socke...

Burnished and lacquered brass check ring at 3/4 inch diameter with a 1/8 IP slip fit, machined from solid brass with a turned edge. Used as a decor...