SATCO/NUVO

A solid four-piece cast brass medium-base lampholder in polished brass, designed for keyless operation where switching happens at the cord or fixtu...

A prewired medium-base lampholder built for custom lamp manufacturing, restoration, and replacement work. The four-piece stamped solid brass shell ...

A pull-chain aluminum socket finished in dark antique brass with a 1/8 IPS cap and screw terminals. The pull-chain mechanism gives the user a tacti...

A medium bi-pin pedestal lampholder with a slide-on shallow base, designed for T8 and T12 fluorescent tubes. The plunger-style end accepts spring-l...

A medium bi-pin pedestal lampholder with a slide-on shallow base and a fixed (stationary) end, designed to pair with a plunger holder at the opposi...

A phenolic medium base snap-in socket sized for 3-1/4" to 4" holders, with a top rim that seats the socket securely against the holder opening. Pre...

A prewired four-piece solid brass medium base lampholder finished in polished nickel for cooler, contemporary lamp builds. The on/off turn knob and...

An unfinished die-cast screw collar loop with ring, threaded for 1/8 IP and rated to 25 pounds maximum. Used as a hanging attachment point on penda...

A prewired medium-base lampholder finished in dark antique brass, built from four-piece stamped solid brass with a longer 10-foot cord for floor la...

A prewired medium-base lampholder with an integrated on/off turn-knob switch, finished in antique brass. The warm antique tone coordinates with tra...

A prewired medium-base lampholder with an integrated on/off turn-knob switch, finished in dark antique brass. Built from four-piece stamped solid b...

A prewired medium-base lampholder finished in antique brass, built from four-piece stamped solid brass. The warm antique brass tone coordinates wit...

A prewired keyless porcelain recessed socket with an integral wireway and 4" leads, built on 2" mounting centers for ceiling and surface-mount fixt...

A polarized quick-connect plug in a clear silver finish, sized for 18/2 SPT-1 lamp cord. Installs without stripping wires for a fast, finished term...

An on-off pull chain socket built from a 3-piece stamped solid brass body with a 1/8 IPS cap and antique brass finish. A lighter, less-expensive al...

A 1/8 IP phenolic socket cap with 1/2 Uno thread, paired with short keyless socket shells that use a plastic bushing. Sold as the cap only for sock...

A 1/8 IP phenolic socket cap with 1/2 Uno thread and integrated set screw, paired with push-thru socket shells that use a plastic bushing. Sold as ...

An E26 phenolic socket shell sized for 1/2 Uno thread — the replacement piece when only the shell needs swapping and the cap stays in service.Featu...

A 3" phenolic candelabra socket with paper liner and a 1/8 IP outside-extrusion double-leg mount for direct fastening to chandelier arms and candel...

An on-off pull chain socket with a 1/4 IPS cap in a polished brite gilt finish, suited to brass and gold-toned lamps where the socket should match ...

A 1-1/8" steel check ring with a curled edge and 1/8 IP slip, finished in antique brass to coordinate with traditional lamp hardware. Drops over th...

An unfinished brass ball nozzle with a 45-degree small angle, used to redirect lamp arms or accessory rods at a fixed bend. The 1/8 IP female-to-ma...

A flat heavy-duty steel crossbar sized at 1 inch by 6 inches, drilled with a 1/8 IP center hole and no additional screw holes. Used as the structur...

A 4-inch brass metal candle cover finished in French gold with a wax-drip exterior, sized to slip over candelabra-base sockets in chandeliers and s...