Fixture Accessories

At a full 2" across, this is the largest 1/8 IP slip check ring in the series — sized for wide shade retainers and oversized shoulder work where th...

Caps a 1/8 IP nipple stack at 1-3/4" diameter, holding the part below it in firm contact with the next shoulder. The wide turned brass face doubles...

Turned brass at 1-7/8" gives this check ring enough face to serve as visible decorative trim while still functioning as a retainer on a 1/8 IP nipp...

At 1-3/8" diameter, this turned brass check ring sits in the broader range of shade and shoulder retainers used in medium-scale fixture builds. Sli...

Solid brass with a turned edge gives this 1-1/8" check ring its clean machined profile and its readiness to accept any decorative finish on top of ...

Holds the next part in a 1/8 IP lamp stack against the nipple shoulder or the part below it. The 1-1/2" turned brass face works as both retainer an...

An unfinished brass check ring at the 1" diameter favored for medium shade retainers and shoulder washers. Slip fits a 1/8 IP nipple and reads clea...

Turned from solid brass and left unfinished, this 7/8" check ring takes plating, lacquer, or hand-aged patinas cleanly. It carries a 1/8 IP slip fi...

Slips over a 1/8 IP nipple and seats against the part above to lock the stack in place. The 3/4" turned brass disc adds a small visible accent wher...

Sized at 5/8" across, this turned brass check ring slips over a 1/8 IP nipple to retain shades, washers, or breaks in a lamp build. The narrow prof...

The taller 1-1/2" version of the burnished-and-lacquered brass riser, raising a finial or shade ring further above the socket cap. Standard 1/4-27 ...

The four-socket version of the cluster head, with the same on/off pull chain control but a fourth lamp added to brighten larger pendants and chande...

The brass-finished version of the cast brass screw collar loop with ring, sized for a 1" canopy hole and a 1/4 IP stem. Carries up to 50 pounds, wi...

This cast brass screw collar loop with ring secures a canopy or fixture body to a 1/4 IP stem, with the threaded loop carrying up to 50 pounds. The...

Malleable iron hickey used to extend or offset a fixture stem, with 1/4 IP threading at both ends. Features Material: Malleable iron Length: 1" ...

The black-cord version of the 8-foot pre-wired pendant assembly, finished with a keyless porcelain socket and ready for a shade or globe. Strain re...

Ready to drop into a pendant or swag fixture, this 8-foot cord set arrives with a keyless porcelain socket, hickey, strain relief, and fiber sleevi...

Intermediate-base porcelain socket with screw terminals and a single-leg mount, sized for E17 intermediate lamps in chandeliers, decorative pendant...

Horizontal screw-down socket for 2-pin compact fluorescent lamps with a G23 and G23-2 base, used in CFL downlights, troffers, and commercial fixtur...

Horizontal snap-in socket for 2-pin compact fluorescent lamps with a G23 and G23-2 base, used in CFL downlights, troffers, and commercial fixture b...

The tallest cover in the ivory Edison-base drip family at 4" — suited to larger chandeliers and grand-scale fixtures where a shorter cover would lo...

Ivory plastic with matching ivory drip detail, sized for Edison medium-base sockets — a warm, classic candle silhouette in the wider bore. Feature...

White plastic with a gold drip accent, sized for Edison medium-base (E26) sockets — a softer, brighter take on the traditional candelabrum look. F...

Black plastic with a gold drip-wax accent in the wider Edison medium-base (E26) sizing — a step up in bore from the candelabra variants, for fixtur...