Fixture Accessories

Three-terminal turn-knob socket wired for two-circuit operation, built in brass with a polished brass finish and a removable knob for traditional l...

Short keyless socket constructed from three-piece stamped solid brass and finished in polished nickel, sized for compact lamp builds and rated for ...

On-off turn-knob socket with a removable knob, built in brass with a polished nickel finish for clean integration into traditional table and floor ...

Three-way turn-knob socket in brass with a polished nickel finish, fitted with a removable knob and set screw for use in two-circuit lamp builds. ...

Polished nickel pull-chain socket built from three-piece stamped solid brass, threaded for 1/8 IPS mounting and rated for higher-load incandescent ...

On-off push-through socket assembled with a set screw, ready to drop into a lamp build without the snap-in retention found on quick-mount versions....

Built as a 5/8-inch socket key extender on a 4/36 mandrel thread, giving turn-knob sockets the added length needed to clear deeper shades or harps....

Extends the reach of a socket turn key by a half inch, threading onto a 4/36 mandrel so a hard-to-reach switch can be turned without disassembly. ...

Brass plated and curled at the rim, this 2-inch steel check ring covers the transition between a 1/4 IP socket and a glass or fabric shade. Featur...

A 3-inch steel check ring that bridges the gap between a 1/8 IP nipple or socket and the shade above it, giving lamp builds a clean, finished trans...

Sized at 1-1/8 inches with a curled outer edge, this steel check ring slips over a 1/4 IP fitting to dress the joint between socket and shade. Fea...

Nickel-plated steel check ring with a softened curled edge, sized at 1-3/4" diameter for 1/8 IP slip lamp pipe. The bright nickel finish coordinate...

Steel check ring at 3-1/4" diameter, brass plated for a warm finish that coordinates with brass fixture hardware. Straight edge and 1/8 IP slip thr...

Steel check ring at 2-3/4" diameter with a clean straight edge, sized for 1/8 IP slip lamp pipe. Unfinished surface accepts paint, plating, or lacq...

Turned brass check ring sized for 1/4 IP slip lamp pipe. The 2-inch diameter and unfinished surface make it easy to plate, lacquer, or patina to ma...

An unfinished brass check ring at 1-7/8" diameter with a 1/4 IP slip fit. The wide turned face reads as visible trim on the assembly while doing th...

Caps a 1/4 IP nipple stack at 1-5/8" diameter, locking the part below in contact with its shoulder. Wide enough to also serve as a visible trim dis...

Solid brass turned to 1-1/2" diameter with a clean machined edge. The unfinished stock accepts plating, lacquer, or aged patinas, while the 1/4 IP ...

An unfinished brass check ring at 1-3/8" diameter, slip fit for 1/4 IP nipples. Sized for broader shade retainers and shoulder work on heavier fixt...

Holds the next component in a 1/4 IP lamp stack at 1-1/8" diameter. The turned brass face works as both retainer and visible trim depending on wher...

At 1-1/4" diameter, this turned brass check ring covers a medium-wide seat on 1/4 IP nipples — common on floor lamps and larger pendant builds. Fe...

An unfinished brass check ring at 7/8" diameter with a 1/4 IP slip fit. The turned edge takes any finish, from polished plating to a natural patina...

Turned from solid brass at 1" diameter, sized for medium shade and shoulder retention on 1/4 IP builds. Unfinished stock for any final finish on to...

Sized at 3/4" diameter, this turned brass check ring sits at the small end of the 1/4 IP slip range — useful where the retainer needs to stay visua...