Fixture Accessories

Smooth-faced vintage canopy kit in dark antique brass, supplied complete with matching mounting hardware. The unadorned 5 inch plate is a versatile...

Polished nickel ribbed vintage canopy kit, supplied with the canopy plate and matching mounting hardware for a finished ceiling installation. The 5...

Nickel plated steel check ring with a curled edge, used to finish off a 1/4 IP slip joint at the bottom of a lamp arm or socket assembly. The curle...

Ribbed 5 inch ceiling canopy in dark antique brass, sold as the canopy plate only for use with existing mounting hardware. The vintage-style ribbed...

Old bronze die cast female loop for hanging pendants and swag fixtures from chains or hooks. The 1/8 IP threading runs through a wireway so the lam...

Old bronze version of the ribbed canopy kit, with the 5 inch diameter, 7/16 inch center hole, two pre-drilled 8/32 bar holes, and 10 pound load rat...

Brushed nickel ribbed canopy kit with mounting hardware included, sized for a 7/16 inch center hole and two 8/32 crossbar screws. The 5 inch diamet...

Same old bronze ribbed canopy in the larger center-hole configuration, 5 inch diameter with a 1-1/16 inch opening for stems and threaded nipples in...

Old bronze finish on the 5 inch ribbed canopy, with a 7/16 inch center hole and two 8/32 bar holes pre-drilled for the crossbar. A warm, traditiona...

Brushed nickel ribbed canopy with a smaller 7/16 inch center hole and two pre-drilled 8/32 bar holes for crossbar mounting. The 5 inch diameter and...

White contemporary canopy that disappears against most ceilings, with the same 5-1/4 inch diameter, 7/16 inch center hole, and two 8/32 bar holes a...

Brass pear-shaped knob in a brushed nickel finish, threaded 8/32 for use as a finial, decorative pull, or visible accent on lamp shades and fixture...

Chrome contemporary canopy with the same 5-1/4 inch profile and standard 7/16 inch center hole, drilled for two 8/32 crossbar screws. The bright re...

Antique brass takes the same 5-1/4 inch contemporary canopy and warms it up for traditional and transitional rooms. The 7/16 inch center hole and t...

Contemporary canopy in a brass finish, 5-1/4 inch diameter with a 7/16 inch center hole and two 8/32 bar holes pre-drilled for standard crossbar mo...

Small blue wire connector with spring inserts, sized for joining up to three #18 AWG conductors. Rated 600V and approved for 105°C supply wire, mak...

Die-cast 1/4 IP screw collar loop with ring in brushed pewter, used to suspend pendants and chandeliers from a hickey, stem, or threaded coupling. ...

The same 5 inch ribbed canopy in a brushed pewter finish, with a 1-1/16 inch center hole for the fixture stem or threaded nipple. A direct replacem...

A 5 inch ribbed canopy in a brushed nickel finish, sized for fixtures with a 1-1/16 inch center hole. The ribbed profile adds a subtle decorative t...

At 1/2 inch across, this curled-edge steel check ring carries a 1/8 IP slip and an antique brass finish. The small diameter suits compact socket cu...

A 2 inch steel check ring with a curled edge, 1/8 IP slip, and an antique brass finish. Dresses the joint between a socket cup and shade holder dur...

A 2 inch steel check ring with a curled edge and 1/4 IP slip center. Used in lamp building to conceal the joint between the socket cup and shade ho...

Curled-edge construction in steel, this 1-1/2 inch check ring carries a 1/4 IP slip center. Sits at the joint between the socket cup and shade hold...

A 1-1/4 inch steel check ring with a curled edge and 1/4 IP slip. Used in lamp assembly to dress the joint between the socket cup and shade holder,...