Lamp Parts

Inline rotary on-off switch in a clear gold housing, sized to install on standard 18/2 parallel lamp cord for click-turn control at the cord itself...

Solid brass nipple in 1/4 IP thread, cut to 3 inches long with a 1/2 inch outside profile and left unfinished for easy soldering, plating, or match...

A 6 inch light duty harp in polished nickel, sized to give medium shades a touch more clearance over the bulb. Steel body, 1/8 IP saddle, 1/4-27 th...

Polished brass finish and a 5-1/2 inch stature make this light duty harp a clean, classic pairing for smaller table lamps and accent fixtures. The ...

At 2 inch height, this nickel plated steel spacer gives the tallest standoff option in the 7/8 inch shaft range. Sized to fit 7/16 inch threaded ro...

Brass plated steel spacer at 2 inch height, the tallest in the 7/8 inch shaft range, providing significant standoff between lamp body components. D...

One inch steel spacer with a brass plated finish, sized to fit standard lamp assemblies over 7/16 inch threaded rod. The 7/8 inch shaft steps down ...

Heavy-duty 10 inch cup harp in a polished nickel finish, built with thicker gauge steel to hold larger and heavier shades than a standard light-dut...

Compact 4 inch light-duty harp in polished nickel, sized for small accent lamps and shorter shades where a taller harp would look out of scale. Two...

Curled-edge steel check ring in an antique brass finish, 1-1/4 inch in diameter with a 1/8 IP slip center. Check rings sit above the socket cap on ...

A taller solid brass spindle at 3/4 inch by 4-1/8 inch, tapped for 1/8 IP thread and supplied unfinished. The extra height suits column and vase-st...

Solid brass neck and spindle in a 1-1/4 by 9/16 inch profile — wider than tall, giving a flatter, more disc-like shoulder for lamp body transitions...

Threaded 1/4 IP end to end and cut to 5-1/2 inches, this zinc-plated steel nipple fits standard pendant stems, ceiling drops, and table lamp bodies...

Steel construction and 1/4 IP threading at both ends make this 5-1/4 inch nipple useful for pendant stems, ceiling fixture drops, and mid-height la...

The 2-1/4 inch length in Satco's 1/4 IP steel nipple lineup. Threaded end to end and zinc plated, sized for short stem runs, coupling extensions, a...

Brass-plated steel check ring in a 1-1/2 inch diameter, with a curled outer edge and 1/4 IP slip center for concealing hardware transitions on lamp...

Compact at 7 inches but built with reinforced steel arms, this heavy-duty lamp harp finishes in dark antique brass to complement warm-tone lamp bas...

Formed from steel and finished in dark antique brass, this 8 inch light-duty lamp harp handles standard shade sizes on residential table and floor ...

A steel lamp harp with a polished brass finish, sized at 4 inches tall for standard shade support in table and floor lamps. The 1/8 IP saddle threa...

Compact 5 inch light duty harp for small accent and buffet lamps where a standard 7 inch harp would sit too tall. Polished nickel finish over steel...

White smooth modern canopy plate, sold as the canopy alone for use with existing mounting hardware. The clean 5 inch face disappears against white ...

Complete ribbed vintage canopy kit in dark antique brass, including the canopy plate and matching mounting hardware for a finished installation. Th...

The same one inch male loop in an old bronze finish, with the 1/8 IP thread, internal wireway, and 10 pound rating that work for smaller pendant ha...

A brass lock-up cap with a black finish, threaded 1/8 IP to seal the open end of a threaded rod or pipe in a lamp assembly. The low 1/4 inch profil...