Lamp Parts

A 1-1/2 inch straight-edge check ring in brass plated steel, used to cap or position lamp parts along a 1/8 IP threaded pipe. A dependable spare fo...

Sized at 1-1/4 inch diameter with a 1/8 IP slip center, this steel check ring provides a clean stop against a threaded lamp pipe during socket, sha...

The 2 inch steel check ring covers wider openings on shades and lamp bases where the smaller sizes fall short. Curled edge, 1/8 IP slip fit, and br...

Step up to a 1-3/4 inch steel check ring with a curled edge for shades and lamp bodies that need a slightly larger cover. Slips over 1/8 IP pipe an...

White-finished die cast 1/4 IP screw collar loop with matching ring keeps the hanging hardware low-profile against light-toned or painted fixtures....

Glossy black die cast 1/4 IP screw collar loop with matching ring pairs cleanly with black chandelier arms and industrial-style fixtures. Handles t...

Bright chrome finish on this die cast 1/4 IP screw collar loop with matching ring pairs it to modern and contemporary fixtures. Rated for a 25 poun...

The antique brass version of the die cast 1/4 IP screw collar loop with matching ring carries the same 25 pound load rating with a warmer, aged fin...

A die cast 1/4 IP screw collar loop with matching ring provides a strong hanging point for shades and glassware, rated to hold up to 25 pounds. The...

A 1-1/4 inch steel check ring with a curled edge slides over 1/8 IP threaded pipe to cover a hole or gap in a shade or lamp body. The brass-plated ...

Three-quarter inch 1/4 IP steel nipple in zinc plate, running thread from end to end. The short-length option in the heavier 1/4 IP range, used whe...

One inch 1/4 IP steel nipple, zinc plated with running thread from end to end. Standard hardware for larger pendants, chandeliers, and ceiling boxe...

Half-inch 1/4 IP steel nipple in zinc plate, running thread the full length. The heavier 1/4 IP thread is the standard for larger fixtures, ceiling...

Four inch zinc plated steel nipple in 1/8 IP, running thread the full length. At this length the nipple starts to serve double duty as a short stem...

Three-and-a-half inch 1/8 IP steel nipple in zinc plate, running thread across the length. Bridges deep vase caps, tall bases, and stacked hardware...

Zinc plated 1/8 IP steel nipple at 3-1/4 inch with running thread the full length. A common length for taller lamp base and canopy stacks where thr...

Two inch zinc plated steel nipple in 1/8 IP with running thread across the length. Long enough to stack multiple washers, check rings, and locknuts...

Zinc plated steel nipple at 2-1/4 inch, 1/8 IP with running thread the full length. Sized for lamp base builds that stack a vase cap, washer, base,...

Steel nipple at 1-7/8 inch, 1/8 IP running thread and zinc plated. A slightly longer option for lamp builders whose stack needs just under two inch...

One-and-a-half inch 1/8 IP steel nipple, zinc plated with running thread end to end. A staple on the bench for socket-to-vase connections, harp bas...

Zinc plated 1/8 IP steel nipple at 1-3/8 inch with running thread the full length. Fills the gap between 1-1/4 inch and 1-1/2 inch stack builds whe...

Steel nipple at 1-1/8 inch, 1/8 IP with running thread the full length and finished in zinc plate. Small-increment sizing between the 1 inch and 1-...

Eight inch length of brass plated steel pipe, 1/8 IP threaded 3/4 inch on each end for direct connection into socket caps, canopies, and loops. A g...

Short four inch brass plated steel pipe, threaded 3/4 inch on both ends in standard 1/8 IP, sized for compact stem work in flush-adjacent pendants ...