Lamp Parts

Caps a 1/4 IP nipple stack at 1-5/8" diameter, locking the part below in contact with its shoulder. Wide enough to also serve as a visible trim dis...

Solid brass turned to 1-1/2" diameter with a clean machined edge. The unfinished stock accepts plating, lacquer, or aged patinas, while the 1/4 IP ...

An unfinished brass check ring at 1-3/8" diameter, slip fit for 1/4 IP nipples. Sized for broader shade retainers and shoulder work on heavier fixt...

Holds the next component in a 1/4 IP lamp stack at 1-1/8" diameter. The turned brass face works as both retainer and visible trim depending on wher...

At 1-1/4" diameter, this turned brass check ring covers a medium-wide seat on 1/4 IP nipples — common on floor lamps and larger pendant builds. Fe...

An unfinished brass check ring at 7/8" diameter with a 1/4 IP slip fit. The turned edge takes any finish, from polished plating to a natural patina...

Turned from solid brass at 1" diameter, sized for medium shade and shoulder retention on 1/4 IP builds. Unfinished stock for any final finish on to...

Sized at 3/4" diameter, this turned brass check ring sits at the small end of the 1/4 IP slip range — useful where the retainer needs to stay visua...

Slips over a 1/4 IP nipple and retains the next part in a heavier lamp stack — floor lamps, larger pendants, or any build using the 1/4 IP system i...

An unfinished brass check ring at the compact 1/2" diameter used where the retainer needs to disappear into the assembly. Slip fits a 1/8 IP nipple...

At a full 2" across, this is the largest 1/8 IP slip check ring in the series — sized for wide shade retainers and oversized shoulder work where th...

Caps a 1/8 IP nipple stack at 1-3/4" diameter, holding the part below it in firm contact with the next shoulder. The wide turned brass face doubles...

Turned brass at 1-7/8" gives this check ring enough face to serve as visible decorative trim while still functioning as a retainer on a 1/8 IP nipp...

At 1-3/8" diameter, this turned brass check ring sits in the broader range of shade and shoulder retainers used in medium-scale fixture builds. Sli...

Solid brass with a turned edge gives this 1-1/8" check ring its clean machined profile and its readiness to accept any decorative finish on top of ...

Holds the next part in a 1/8 IP lamp stack against the nipple shoulder or the part below it. The 1-1/2" turned brass face works as both retainer an...

An unfinished brass check ring at the 1" diameter favored for medium shade retainers and shoulder washers. Slip fits a 1/8 IP nipple and reads clea...

Turned from solid brass and left unfinished, this 7/8" check ring takes plating, lacquer, or hand-aged patinas cleanly. It carries a 1/8 IP slip fi...

Slips over a 1/8 IP nipple and seats against the part above to lock the stack in place. The 3/4" turned brass disc adds a small visible accent wher...

Sized at 5/8" across, this turned brass check ring slips over a 1/8 IP nipple to retain shades, washers, or breaks in a lamp build. The narrow prof...

The taller 1-1/2" version of the burnished-and-lacquered brass riser, raising a finial or shade ring further above the socket cap. Standard 1/4-27 ...

The brass-finished version of the cast brass screw collar loop with ring, sized for a 1" canopy hole and a 1/4 IP stem. Carries up to 50 pounds, wi...

This cast brass screw collar loop with ring secures a canopy or fixture body to a 1/4 IP stem, with the threaded loop carrying up to 50 pounds. The...

Malleable iron hickey used to extend or offset a fixture stem, with 1/4 IP threading at both ends. Features Material: Malleable iron Length: 1" ...