Lamp Parts

Brushed nickel ribbed canopy kit with mounting hardware included, sized for a 7/16 inch center hole and two 8/32 crossbar screws. The 5 inch diamet...

Same old bronze ribbed canopy in the larger center-hole configuration, 5 inch diameter with a 1-1/16 inch opening for stems and threaded nipples in...

Old bronze finish on the 5 inch ribbed canopy, with a 7/16 inch center hole and two 8/32 bar holes pre-drilled for the crossbar. A warm, traditiona...

Brushed nickel ribbed canopy with a smaller 7/16 inch center hole and two pre-drilled 8/32 bar holes for crossbar mounting. The 5 inch diameter and...

White contemporary canopy that disappears against most ceilings, with the same 5-1/4 inch diameter, 7/16 inch center hole, and two 8/32 bar holes a...

Brass pear-shaped knob in a brushed nickel finish, threaded 8/32 for use as a finial, decorative pull, or visible accent on lamp shades and fixture...

Black finish on the 5-1/4 inch contemporary canopy gives a clean, recessive look at the ceiling, useful when the goal is to let the fixture itself ...

Chrome contemporary canopy with the same 5-1/4 inch profile and standard 7/16 inch center hole, drilled for two 8/32 crossbar screws. The bright re...

Antique brass takes the same 5-1/4 inch contemporary canopy and warms it up for traditional and transitional rooms. The 7/16 inch center hole and t...

Contemporary canopy in a brass finish, 5-1/4 inch diameter with a 7/16 inch center hole and two 8/32 bar holes pre-drilled for standard crossbar mo...

Die-cast 1/4 IP screw collar loop with ring in brushed pewter, used to suspend pendants and chandeliers from a hickey, stem, or threaded coupling. ...

The same 5 inch ribbed canopy in a brushed pewter finish, with a 1-1/16 inch center hole for the fixture stem or threaded nipple. A direct replacem...

A 5 inch ribbed canopy in a brushed nickel finish, sized for fixtures with a 1-1/16 inch center hole. The ribbed profile adds a subtle decorative t...

At 1/2 inch across, this curled-edge steel check ring carries a 1/8 IP slip and an antique brass finish. The small diameter suits compact socket cu...

A 2 inch steel check ring with a curled edge, 1/8 IP slip, and an antique brass finish. Dresses the joint between a socket cup and shade holder dur...

A 2 inch steel check ring with a curled edge and 1/4 IP slip center. Used in lamp building to conceal the joint between the socket cup and shade ho...

Curled-edge construction in steel, this 1-1/2 inch check ring carries a 1/4 IP slip center. Sits at the joint between the socket cup and shade hold...

A 1-1/4 inch steel check ring with a curled edge and 1/4 IP slip. Used in lamp assembly to dress the joint between the socket cup and shade holder,...

A 1 inch steel check ring with a curled edge and 1/4 IP slip, plated in nickel. Used in lamp assembly to dress the joint between the socket cup and...

A 1-3/8 inch nickel-plated steel check ring with a curled edge and 1/8 IP slip. Sized to dress the joint at a socket cup or shade holder, it adds a...

7/8 inch antique brass check ring in curled-edge steel, bored 1/8 IP slip. Pairs cleanly with standard socket cups and harp bottoms where an antiqu...

A 2 inch steel check ring with a curled edge and 1/8 IP slip center hole. Used in lamp building to conceal the joint between a socket cup and shade...

5/8 inch antique brass check ring in curled-edge steel, bored 1/8 IP slip. The smallest of the antique-brass curled rings, suited to tight stem-and...

3 inch brass-plated check ring in straight-edge steel, bored 1/8 IP slip. The larger diameter and flat profile work well as a base trim or shoulder...