Lamp Parts

A 5-3/4 inch 1/4 IP steel nipple, zinc plated for a bright silver finish. Threaded end to end and sized for pendant stems, ceiling fixture drops, a...

A 4-3/4 inch 1/4 IP steel nipple, threaded both ends and zinc plated. Sized for pendant stems, ceiling fixture drops, and lamp body sections where ...

Zinc-plated 1/4 IP steel nipple at 4-1/4 inches, sized for stem extensions on ceiling fixtures, pendant drops, and lamp bodies that need a mid-leng...

Cut to 1-3/8 inches with 1/4 IP threading on both ends, this steel nipple bridges close-fitting hardware on ceiling fixtures, pendants, and lamp bo...

Zinc-plated 1/4 IP steel nipple cut to 1-1/8 inches, threaded end to end. Sized for compact joins between canopy, coupling, and stem hardware on ce...

A stubby 1/4 IP steel nipple at 7/8 inch, sized for tight close-nipple joins where two fittings need to meet with minimal shaft between them. Zinc ...

A short 1/8 IP steel nipple at 1-5/8 inches, threaded both ends and zinc plated. Sized for close-coupling work: attaching sockets to lamp caps, joi...

An oversized 1/8 IP steel nipple threaded end to end, zinc plated for a bright silver finish. Sized for full-height torchieres, extended pendant dr...

Four feet of threaded 1/8 IP steel, zinc plated, cut for the longest lamp bodies in a typical shop: full-height torchieres, deep-drop pendants, and...

At 45 inches, this 1/8 IP steel nipple lands in oversized-fixture territory: tall torchieres, long pendant drops, and custom floor lamps built arou...

Threaded end to end in 1/8 IP with a 20-inch reach, this zinc-plated steel nipple is cut for tall floor lamps, extended pendant drops, and multi-se...

An 18-inch 1/8 IP steel nipple for lamp bodies and pendant stems that need real length. Threaded both ends and zinc plated for a uniform silver fin...

Steel construction and 1/8 IP threading at both ends make this 16-inch nipple a workhorse for floor lamp bodies, tall pendants, and stem-hung fixtu...

The 14-inch length in this 1/8 IP steel nipple lineup, threaded end to end and finished in zinc plate for a bright silver appearance. Sized for flo...

Zinc-plated steel nipple threaded 1/8 IP at both ends, cut to 11 inches for extended lamp bodies, tall candlestick fixtures, and pendant assemblies...

A 9-inch threaded steel nipple with a 1/8 IP thread pattern, sized for building out taller lamp bodies and multi-tier pendant stems. Zinc plating g...

Solid brass half-ball in a 3/4 inch diameter, unfinished for custom polishing or patina work. The 1/8 tap threads directly onto standard lamp pipe ...

A 5/8 inch unfinished brass half-ball with a 1/8 tap, ready for polishing, lacquering, or antiquing to match custom lamp hardware. Adds a rounded d...

An unfinished half-ball cap in solid brass with a 1/2 inch diameter, used as a decorative accent or transition piece on custom lamp assemblies and ...

Unfinished steel check ring measuring 1-1/2 inches across, with a 1/4 IP slip center and a curled outer edge. Used to hide the top opening of a soc...

Eight inches of vertical clearance, dark antique brass over heavy-gauge steel, and a 1/8 IP saddle sized to standard lamp pipe — a workhorse harp f...

Sized at 9 inches for taller drum and pleated shades, this light-duty lamp harp finishes in dark antique brass over steel construction. The 1/8 IP ...

A 7 inch light-duty lamp harp in dark antique brass, formed from steel and sized for smaller shades on table lamps and accent fixtures. The 1/8 IP ...

Support larger drum and empire shades with this 9-1/2 inch heavy-duty lamp harp, finished in dark antique brass to coordinate with warm-tone hardwa...