Lamp Parts

Steel construction with a yellow zinc plated finish gives this 3-1/4 inch 1/8 IP nipple the rigidity and corrosion protection required for lasting ...

Connect sockets, canopies, and shade holders with a 3 inch 1/8 IP steel nipple in a yellow zinc plated finish. Threaded through the full length for...

A 2-1/2 inch steel lamp nipple threaded 1/8 IP on both ends, finished in yellow zinc plating for corrosion resistance and a warm neutral tone that ...

Two-inch 1/8 IP steel nipple with a yellow zinc-plated finish, at the long end of the standard nipple range. Useful for deep canopy assemblies, tal...

A 1-3/4 inch length 1/8 IP steel nipple in yellow zinc plate, for lamp builds that stack multiple pieces of hardware on a single threaded shaft. Co...

Extended 1-1/2 inch 1/8 IP steel nipple, yellow zinc-plated, for lamp assemblies that need extra depth through a thick canopy or a stacked hardware...

One-inch 1/8 IP steel nipple with a yellow zinc-plated finish, long enough to bridge a deep canopy or clear a stacked check ring and washer assembl...

Inline on-off cord switch designed to install midway along 18/2 SPT-2 lamp cord, giving table lamps, floor lamps, and accent fixtures a convenient ...

Standard 1/8 IP steel nipple in zinc plated finish, 60 inch length for stem-hung pendants and chandeliers dropping from tall residential and light ...

Heavier 3/8 IP steel nipple, zinc plated, cut to 48 inch length for larger chandeliers and commercial pendants that need a wider-diameter stem to c...

72 inch steel nipple threaded 1/8 IP end to end, finished in bright zinc for use in stem-hung pendants and chandeliers over very tall spaces. Cut t...

Long 60 inch steel nipple with 1/8 IP threading and a yellow zinc plated finish, used where a fixture stem needs to span from a high ceiling down t...

Yellow zinc plated steel nipple with 1/8 IP threading, cut to 30 inch length for long stem hanging fixtures, extended pendants, and vertical drops....

Cast brass screw collar loop finished in nickel, threaded 1/4 IP for standard lamp assemblies. A sturdy hanging attachment for pendants and drops w...

Brass-plated steel riser used as a spacer or decorative extension in lamp assemblies. The 1/4-27 thread matches finials and thread caps, and the pl...

Extra-long 50 inch steel nipple in 1/4 IP thread with a zinc-plated finish. Standard drop-tube length for pool table lights, kitchen island pendant...

Cream plastic candle cover that slips over a candelabra socket to give chandelier and sconce fixtures a traditional candle silhouette. Slightly war...

Porcelain-bodied GU24 ceiling receptacle built for higher-heat applications, with an integrated pull chain switch and pre-wired 6 inch black/white ...

Unfinished 1/4 IP steel nipple in the 48 inch long-run length, ready for plating, painting, or hidden runs where the raw finish never shows. Same 1...

Long-run 1/4 IP steel nipple in a 48 inch length, zinc plated for corrosion protection where a threaded stem needs to travel through decks, canopie...

White plastic candle cover sized for medium-base sockets, at 1-3/4 inches tall with a wider 1-1/4 inch outside diameter. The short profile suits fl...

Light duty 15 inch harp in polished nickel for medium and smaller shades that need a slimmer frame. Ships with the standard 1/8 IP saddle and 1/4-2...

Light duty version of the 15 inch harp in polished brass, sized for medium to smaller shades that don't need heavy gauge support. The slimmer profi...

The polished nickel version of the 15 inch heavy duty harp, giving contemporary and transitional lamps a cooler-toned frame to pair with brushed or...