Lamp Parts

Flanged steel neck in antique brass, 1-1/2 inch height, offering a taller transition profile between lamp body components while maintaining the sam...

Steel cap nut with an 8/32 thread in a brushed nickel finish, used as a finished cover where a bolt or threaded post would otherwise be visible on ...

Cap nuts finish exposed thread ends on lamp base assemblies and hardware stacks, giving a clean domed profile in place of a raw nut. Steel construc...

A steel double crossbar with two sets of screw holes at 2-3/4 inch and 3-7/8 inch center-to-center, giving installers flexibility to match the moun...

Low-profile brass-plated flanged steel neck: 1/2 inch height with a 7/8 inch bottom seat, giving lamp builders a thin transitional collar between t...

Five round head screws in 8/32 thread, finished in brass plate for a warm traditional look. The rounded head sits proud on a canopy or shade holder...

Sized for 5 inch neckless glass globes, this white-finished holder includes the retaining insert that grips the shade opening from inside. A drop-i...

1-3/4" brass ball, tapped 1/8 IP. A substantial size for oversized finials and bold decorative accents on chandeliers and statement fixtures. Unfin...

Bottom turn-knob socket in bakelite construction, factory-wired with 13 inch black and white leads for direct installation into lamp bodies. Rated ...

Polished and lacquered 3/8 IP screw collar loop in solid cast brass, built to fit a 1 inch canopy hole with a 1-1/8 inch ring. The larger 3/8 IP th...

This 4 inch crossbar is threaded for 1/8 IP nipples, the standard threaded rod size used to hang most pendants and ceiling fixtures. Features S...

Nickel-plated 1 inch flanged steel neck with a 7/8 inch bottom seat, a common size for transitioning between the lamp body and socket hardware on s...

Unfinished brass round knurled locknut threaded for 1/8 IP, with a knurled edge that lets the nut be tightened by hand when wrench access is tight....

Unfinished brass armback with four 1/8 IP threaded holes, giving lamp makers a compact junction point for multi-arm chandelier and sconce assemblie...

Round beaded brass locknut for 1/8 IP lamp pipe. The decorative beaded edge adds a finished look where the nut shows, while the brass blank accepts...

Reducing bushing machined from solid brass, threaded 1/8 F on one end and 3/8 F on the other for stepping between two common lamp pipe sizes.Featur...

A 4 inch crossbar bundled with a hickey and adapter, this hardware set handles the mounting side of most ceiling fixture installs without needing e...

A 3-way rotary lamp switch for use with 3-way bulbs, giving you low, medium, and high brightness settings from a single knob. Standard hardware for...

Two-inch brass ball with a 1/8 IP tap, the largest in the series. Use as a major finial or decorative anchor on chandeliers, hall fixtures, and ove...

A brass-plated steel cap nut with 8/32 threading, used to conceal exposed threaded rod ends on lamp finials, harp holders, and shade risers. Featur...

Solid brass ball armback in a 7/8 inch by 1-1/16 inch size with two 1/4 IP threaded entries, unfinished for downstream plating. The heavier thread ...

Compact 3/8 inch knurled brass knob with an 8/32 female thread, finished in a burnished-and-lacquered treatment that locks in a warm brass tone and...

One inch flanged steel neck in antique brass, sized as a short transition piece between lamp body sections. The flange gives adjoining parts a stab...

Round knurled brass locknut for 1/8 IP lamp pipe. The knurled edge gives a positive grip for hand tightening, and the unfinished surface accepts pl...